Gypsum tiles must be laid correctly, as not just the aesthetic look of cosmetic facing, but in addition the service quality of the

substance will depend on the technologies of work. The product is more universal, and it may be connected to concrete, plaster,

brick or gypsum board sheets, and provided that the top layer of the base is even and has no flaws.

In the event the defects of this foundation are significant, it should be completely treated with primer, and then a cement mortar

is created, which fills all of the cracks. Then the surface should be primed and dried. Primer treatment is necessary to improve

the bond between the tile and the walls. In cases like this, its composition should choose a particular, comprising components

which stop the appearance of fungus and mould.

In the modern interior of the rooms most often used gypsum tiles, imitating natural brick or stone. To carry out cosmetic

finishing your self, it’s essential first of all to select a strategy of tile positioning and prepare a remedy. It’s necessary to

pay attention to the reverse side of the substance. If its surface includes an embossed surface, then the adhesive should be put

with an trowel, and if it is even, then with a top notch one.

The technologies of the work is as follows:

* A thin layer of glue mortar is applied to the pre-prepared wall. It is spread over the foundation so it is likely to put 4-5

tiles. Decorative cladding can be placed both on plasterboard, and on putty.

* Glue the rear side of these tiles with glue.

* Plaster components are pressed against the wall and their place is corrected. To align with the seams, it is suggested to use

spacers.

* Finishing is performed in rows, each of which ought to be changed by half a tile. Facing is completed into the corners of the

space, then immediately get rid of any residual mortar in the joints.

Drying the walls requires no more than a day also demands a continuous humidity and temperature within the room. The last point in

the laying of gypsum tiles is their decoration. To do this, the joints between the elements are filled with a special solution,

the color of which matches the brick.

Decorative imitation of brickwork around the walls will be carried out in the following ways:

* Cutting the darkened surface of the pits of masonry with a bolt cutter with your own hands;

* placing of tiles beneath the brick:

* imitating the format and color of the side surface of a single brick;

* Imitating a fragment of brickwork of several bricks.

The ideal method to decorate»beneath the brick» will be the one which allows you to create a practical coating with the maximum

appearance of its similarity to natural masonry. All three strategies to conduct this sort of finishing works fulfill the demands,

however, the cutting of joints using a bolt will be labor-intensive and the formation of considerable quantities of dust, so masterfasada.ru let

us consider more typical ways.

The old finish is removed from the walls, and the surface, if needed, is leveled to get rid of the need to glue plaster onto a

thick layer of adhesive.

Combining such cladding with other kinds of interior finishes could be both systematic and done with no apparent consistency,

chaotically, together with fake of signs of aging.

With the support of cosmetic gypsum tiles it is possible to mimic a large number of textures.

A lot of textures may be imitated with the help of decorative gypsum tiles.

The wall on which it’s to be installed must possess the following attributes:

* Hardness and strength of the surface;

* The lack of uneven locations and sharp gaps;

* not any deformations.

Cosmetic tiles in the interior of this kitchen

Walls are made from a number of materials, let us break down the principles of installation.

When working with concrete, there will be no big problems. It is only essential to take into account the porosity of the material.

Concrete, which has virtually no pronounced pores, should be treated with a fantastic primer.

Mounting gypsum tiles on concrete

Before starting work on the installation of gypsum tiles in the walls, then it is well worth checking the strength of this

surface. When the plaster does not drop off the wall and at exactly the exact same time holds nicely, it’s possible to simply

paint it with primer.

Mount the tiles onto the painted concrete shouldn’t. The surface should be scratched, ensuring to misfire, and it needs to be

grouted and covered with a layer of plaster.